DM8806: 6-Port Ethernet Single Chip Switch Controller mit GMII/MII/RMII
Features
• Ethernet Switch with five 10/100Mb PHY, five 10/100Mb MAC and one MII/RevMII
• compatible to IEEE802.3u and IEEE802.3az
• Temperature Range: 0°C to 70°C and -40° to 85°C
• Fiber mode FEF (Far End Fault)
• 50MHz clock out for RMII Interface
• Cut-thru function and Store-and-forward
• Per port supports 4 priority queues , Port-based, 802.1P VLAN, MAC based, IPv4 TOS
• Supports 802.1Q/port-based VLAN up-to 16 VLAN group with full 12-bit VID: tag/untag
• Per port support bandwidth, ingress and egress rate control
• Supports Broadcast Storming filter function
• Supports Back Pressure Flow Control in Half-duplex mode.
• Recodes up-to 2K Uni/Multi-cast MAC addresses
• Automatic aging scheme
• Support MIB counter
• Support multicast filter function
• Register access by MDC/MDIO format
• Support trunk ports
Block Diagam DM8806
Der DM8806 ist ein voll integrierter Fast Ethernet Switch-Controller für normalen und erweiterten Temperaturbereich mit fünf 10/100Mb PHY, fünf 10/100Mb MAC plus einem 10/100/1000Mb MAC, und einer MII/GMII-Schnittstellenoption für einen 6. MAC.
Der Controller bietet grundlegende Layer-2-Switch-Funktionen und erweitertes IEEE 802.1Q VLAN, Priority Queuing, IEEE 802.3az Energy Efficient Ethernet, IGMP snooping und Spanning Tree protocol.
Alle Ports unterstützen FX, nur die Ports 0 und 1 unterstützen LFP/FEF. Für den Fiber-Modus wird ein EEPROM benötigt. Es wird nur PTPv1 boundary clock unterstützt.
Die integrierten PHYs sind konform mit den IEEE 802.3u Standards. Die MII/GMII-Schnittstelle bietet die Möglichkeit zum flexiblen Anschluss von 10/100/1000Mb PHYs.
Im Mode 2A (unterschiedliche Pinbelegung zu Mode 3) können der GMAC und das GMII Interface benutzt werden. Details dazu im separaten Datenblatt zu Mode 2A und der Einführung zum DM8806.
Das Standard EVB des DM8806 ist auf Mode 3 konfiguriert.
General
01 Davicom General Layout Guide | 718.85 KB | |
02 Davicom Hardware Layout Guide | 9.4 MB | |
03 DACOM Ethernet Design-In Guide | 2.64 MB | |
04 Connecting two MII devices without transformers | 76.04 KB | |
05 Design hint Center-Tabs Transformer to PHY | 305.47 KB | |
06 Crystal Information | 58.87 KB | |
07 Programming Reference Flow-Chart | 130.04 KB |
Part-Specific
11 DM8xxx Crossed RMII | 91.26 KB | |
12 DM8xxx Reduced MII | 46.54 KB | |
13 DM8xxx Reverse MI | 89.93 KB | |
14 DM8xxx Reverse RMII | 70.76 KB | |
15 DM8806 introduction and application | 90.73 KB | |
16 DM8806 EVB Schematic Mode 3 | 111.77 KB | |
17 DM8806 Schematic Demo Board Mode 2A Gigabit MAC | 222.65 KB | |
18 DM8xxx Programming Guide | 163.22 KB | |
19 DM8806 Reliabilty Test Report | 112.34 KB | |
20 DM8806 Cut-Through Configuration and Use | 167.85 KB | |
21 DM8806 10-port GPHY M2A | 164.63 KB | |
22 DM8806 Demo Board Jumpers Definitions | 37.5 KB |